3D GLW Series SiO2 Ceramic Trim Restore 473ml.

Solvent-free mirror glue. Bonding of mirrors with silver amalgam according to DIN 1238 and plastic mirrors. For gluing window panes. Odorless, water resistant. Permanently elastic and resistant to aging. Does not contain silicone. Areas of application Gluing mirrors on doors and walls. Glazing with mirrors on walls, offices, shops, restaurants, discotheques, etc. The adhesive is applicable on walls with plaster and concrete, surfaces made of wood materials, chipboard, plasterboard, etc. Applicable on Styrofoam surfaces. Work instructions Base - walls or ceilings must be well cleaned, dry and degreased. Remains of paint or plaster must be removed in advance. Do not stick to damp or wet substrates. Assembling the details - from 5 to 10 minutes after applying the glue, after which the mirror is installed and pressed well to the base. Fastening - mirrors with a thickness of 2 to 4 mm can be glued to a vertical wall without additional fastening. The glue is applied evenly in straight vertical stripes with a distance between them of about 10 cm (see sketch). For large vertical mirrors with a thickness of 6 to 8 mm and those that are mounted on surfaces/substrates at an angle, additional reinforcement of the mirror is required until the glue dries and sets. Fixation - large mirrors should be fixed for about 12 hours. Air access must be ensured to the rear of the mirror. Consumption - about 1 hard pack per m at a thickness of 6 to 8 mm. Cleaning - in liquid state with LU-cleaner with Art. No. 0890 108. In the hardened state, it can only be removed mechanically. Gluing plastic PMMA mirrors ICE Perspex: Bronze, Silver, Gold. Roehm und Haas: bronze, gold. Plexiglas XT: colorless. "Altulor" plastic mirrors. In these types of mirrors, no damage to the mirror surface has been found and the tolerance of the materials to each other is good. PMMA mirrors have a high coefficient of linear deformation and for this reason a very smooth surface and proper fixing is required until the glue hardens. The installation of the PMMA mirrors is done using the glue for mirrors up to the recommended dimensions of 600x600 mm. The instructions for use and operation provided by us are advisory and are based on our tests and trials. Due to the presence of numerous applications of the products, conditions of storage and operation, we do not take responsibility for a specific result obtained after using our product. To the extent that our free customer service provides technical information or acts as an advisory service, this liability is not assumed by the service in question, except where the advice or information provided falls within the scope of our specific, agreed upon service or the advisor acts intentionally. We guarantee constant quality of our products. We reserve the right to make technical changes and further develop our products. Chemical basis Polymeric rubber Density 1.4 g/cm3 Open working time about 15 minutes at +20°C/50% RH. humidity Operating temperature +5°C to +30°C Maximum temperature resistance +100°C Allowable total deformation 25% Shrinkage <5% Shore A hardness around 30 Tensile strength 0.8 N/mm² Shelf life 12 months from +5°C to +30°C

The all-rounder for concrete, masonry and post-installed rebar connections Two-part reactive resin mortar, styrene-free vinylester Individual fixing point, cracked and uncracked concrete, seismic performance category C1 Anchor rod W-VI-A, anchor rod W-VD-A, standard threaded rod with acceptance test certificate 3.1 Masonry individual fixing point (system with perforated sleeve WIT-SH): Perforated sleeve WIT-SH, anchor rod WIT-AS, internally threaded sleeve WIT-IG Masonry individual fixing point (system with perforated sleeve SH): Perforated sleeve SH, anchor rod W-VI-A, standard threaded rod with acceptance certificate 3.1 Post-installed rebar connection Proof of Performance European Technical Assessment ETA-12/0164: Individual fixing point + cracked and uncracked concrete (anchor rod W-VD-A, standard threaded rod with acceptance test certificate 3.1), seismic performance category C1 European Technical Assessment ETA-13/1040: Individual fixing point + masonry consisting of solid and perforated brick, aerated concrete (perforated sleeve WIT-SH, anchor rod WIT-AS, internally threaded sleeve WIT-IG, aerated concrete only with perforated sleeve WIT-SH 18x95) European Technical Assessment ETA-16/0757 and ETA-20/0854: Individual fixing point + masonry consisting of solid and perforated brick, aerated concrete (perforated sleeve SH, anchor rod W-VI-A, internally threaded sleeve, threaded rod with acceptance test certificate 3.1, aerated concrete only without perforated sleeve) European Technical Assessment ETA-12/0166: Post-installed rebar connection, 330 ml, 420 ml, 825 ml cartridges only