VEMO V20-72-5246 Sensor, fuel pressure

Solvent-free mirror glue. Bonding of mirrors with silver amalgam according to DIN 1238 and plastic mirrors. For gluing window panes. Odorless, water resistant. Permanently elastic and resistant to aging. Does not contain silicone. Areas of application Gluing mirrors on doors and walls. Glazing with mirrors on walls, offices, shops, restaurants, discotheques, etc. The adhesive is applicable on walls with plaster and concrete, surfaces made of wood materials, chipboard, plasterboard, etc. Applicable on Styrofoam surfaces. Work instructions Base - walls or ceilings must be well cleaned, dry and degreased. Remains of paint or plaster must be removed in advance. Do not stick to damp or wet substrates. Assembling the details - from 5 to 10 minutes after applying the glue, after which the mirror is installed and pressed well to the base. Fastening - mirrors with a thickness of 2 to 4 mm can be glued to a vertical wall without additional fastening. The glue is applied evenly in straight vertical stripes with a distance between them of about 10 cm (see sketch). For large vertical mirrors with a thickness of 6 to 8 mm and those that are mounted on surfaces/substrates at an angle, additional reinforcement of the mirror is required until the glue dries and sets. Fixation - large mirrors should be fixed for about 12 hours. Air access must be ensured to the rear of the mirror. Consumption - about 1 hard pack per m at a thickness of 6 to 8 mm. Cleaning - in liquid state with LU-cleaner with Art. No. 0890 108. In the hardened state, it can only be removed mechanically. Gluing plastic PMMA mirrors ICE Perspex: Bronze, Silver, Gold. Roehm und Haas: bronze, gold. Plexiglas XT: colorless. "Altulor" plastic mirrors. In these types of mirrors, no damage to the mirror surface has been found and the tolerance of the materials to each other is good. PMMA mirrors have a high coefficient of linear deformation and for this reason a very smooth surface and proper fixing is required until the glue hardens. The installation of the PMMA mirrors is done using the glue for mirrors up to the recommended dimensions of 600x600 mm. The instructions for use and operation provided by us are advisory and are based on our tests and trials. Due to the presence of numerous applications of the products, conditions of storage and operation, we do not take responsibility for a specific result obtained after using our product. To the extent that our free customer service provides technical information or acts as an advisory service, this liability is not assumed by the service in question, except where the advice or information provided falls within the scope of our specific, agreed upon service or the advisor acts intentionally. We guarantee constant quality of our products. We reserve the right to make technical changes and further develop our products. Chemical basis Polymeric rubber Density 1.4 g/cm3 Open working time about 15 minutes at +20°C/50% RH. humidity Operating temperature +5°C to +30°C Maximum temperature resistance +100°C Allowable total deformation 25% Shrinkage <5% Shore A hardness around 30 Tensile strength 0.8 N/mm² Shelf life 12 months from +5°C to +30°C

Reliable hardening at low temperatures around 0°C Assists in winter use High degree of gap bridging Completely fills extensive surface roughnesses Gap filling capacity of 0.15 mm Even extremely large deviations are cost effective to correct. Prevents frictional corrosion The bearings will not seize up. Resistant to a large number of bases, gases, solvents, oils and fuels Silicone-free, solvent-free and oil-free DOS system: Practical one-handed operation thanks to the clever turn-lock nozzle One hand always remains free. Continuously adjustable dispensing system Dispensing can be adjusted to suit the application, and to keep consumption and costs to a minimum. No residue material in dispensing neck Costs optimised thanks to emptying with virtually no remaining product Notice The following plastics can be affected in the event of prolonged exposure: ABS, celluloid, polystyrene, polycarbonate (Macrolon), PMMA (Plexiglas), polysulfone, SAN (lurane, Tyril), Vinidur, vulcanised fibre, and painted surfaces. We always recommend that you conduct your own tests. NSF-registered, Class S5, bearing retaining compound NSF-tested in accordance with NSF/ANSI 61 for use in service water and drinking water up to +82°C The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. If our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet! Application area For high-strength securing of cylindrical joining parts such as bushings and sleeves as supplied, ball bearings, oil-impregnated sinter bronze, gears, bolts, shaft and hub connections exposed to high loads. The bearing retaining compound is designed for use in the automotive and commercial vehicle industry, in metalworking and tool manufacturing, shipbuilding, mechanical engineering and engine construction, electrical and electronics construction, food, beverage, pharmaceutical and paper industries, etc. Instructions This liquid plastic cures when in contact with metal in the absence of oxygen. The contact surfaces must be dry, dust-free and grease-free. Moisten the adhesive surfaces sufficiently and put them together immediately. For more information, please refer to the technical data sheet.