Xado ХА 40278 Diesel economy additive 500ml

XADO 1 Stage Engine Revitalizant is a 1-step engine treatment that rebuilds metal and protects worn metal from future wear. One 27ml tube contains enough active ingredient for a complete 100% (RF100) cycle of revitalization for an automobile engine. The difference between this product and 1 Stage Maximum Atomic Metal Conditioner is this product is only the raw, active ingredient – Revitalizant - in gel form. Revitalizant has been independently tested and proven to increase compression, decrease fuel consumption, increase horsepower, and reduce toxic emissions. No matter how well a car is maintained, high heat and friction cause a car’s engine to become worn, scratched, and mis-shaped over time. Adding just a tube of XADO 1 Stage Engine Revitalizant to your engine oil rebuilds worn engine metal and coats the rebuilt metal at the friction points with a self-regulating layer of ceramic-metal to prevent future wear. Unlike other engine treatments that must be added during every oil change, 1 Stage Engine Revitalizant needs to be added only ONCE for 62,000 miles of protection. XADO’s innovative patented nano-technology is the result of 20 years of research and development. When added to an automobile’s engine oil, Revitalizant rebuilds worn engine metal at the atomic level, reversing wear, restoring engine geometry, and coating engine metal with a layer of ceramic-metal to protect against future wear. Revitalizant is activated by high-heat and friction, so it only repairs metal at high-friction points where metal wear occurs. Revitalizant leaves crank-cases and non-friction metal unaffected. The protective layer of Revitalizant does not cake, flake, or alter oil viscosity. This makes it safe to use in even the most sensitive vehicles. 1 Stage is compatible with all motor oils, from full-synthetic to mineral. XADO’s Revitalizant technology has been independently tested and proven to work Make sure the automobile engine is warmed up to normal operating temperature. Turn off the vehicle. Insure the tube is at room temperature so that contents flow freely. Empty contents of the tube into the engine oil reservoir. Start the car and let the engine idle for five minutes. Then drive as you normally would. It takes 600 to 900 miles to complete the Revitalization cycle, during which changing oil is NOT recommended. *Granules of Revitalizant completely dissolve in motor oil at normal operating temperature. *1 tube treats an automobile engine with an oil capacity of 10 quarts of oil. Additional treatments are necessary for larger engines with higher oil capacities. As a general rule, use one tube of 1-Stage for every 10 quarts of oil. *Keep out of reach of children. Avoid contact with skin and eyes. If swallowed, seek medical attention immediately and show the container or label to medical personnel. Avoid release into the environment; refer to special instructions/ Material Safety Data Sheet. *Material Safety Data Sheet is available for professional user on request. Note 1 Stage Engine Revitalizant works in all gasoline-powered, natural-gas, and diesel engines of passenger cars and small trucks and 4-stroke motorcycles with oil system up to 10 Quarts Can be combined with all types of motor oils, from full synthetic to mineral oils It takes 600 to 900 miles to complete the Revitalization cycle, during which changing oil is NOT recommended Repeated application of 1 Stage Engine Revitalizant is recommended after 62,000 miles For the highest level of protection for your automobile engine use XADO Atomic Oil or XADO HighWayMetal Conditioner (RF5.5) during each oil change. XADO Highway contains 5.5% (RF5.5) of the Active ingredient necessary for 1 complete revitalization cycle. A complete oil change using XADO Atomic Oil also provides 5.5% (RF5.5) of the revitalization necessary for a complete Revitalization cycle Technology and certificates 3C EFFECT 3G generation Rebuilds worn engine metal and reverses metal wear Restores lost compression in cylinders Improves engine power and acceleration Reduces fuel consumption Restores oil pressure Can double or triple the life of an engine Protects against damage from cold starts Decreases toxic carbon monoxide and dioxide emissions

ATOMEX PETROL MULTI CLEANER IS A HIGH PERFORMANCE FUEL SYSTEM CLEANER FOR GASOLINE ENGINE. Cleans fuel system up to the level of technical purity. Offers perfect alternative to a bench cleaning of injectors. Improves fuel pump performance. Reliably protects fuel system. During the regular car operation and driving on standard gasoline, deposits are unavoidably formed in the fuel system. These deposits decrease engine power, increase fuel consumption and toxicity of the exhaust gases, increase detonation risk and cause vibrations. Solution: regular cleaning of the fuel system by using Atomex Petrol Multi Cleaner. Accidental water entry or fueling with contaminated fuel may cause pump breakage, hanging-up of injector needles. Solution: revitalizant contained in the cleaner will reliably protect parts of fuel equipment, pump and injector against wear. APPLICATION INSTRUCTIONS Pour the AtomEX Petrol Multi Cleaner product into a fuel tank before fueling. NOTE The Atomex Petrol Multi Cleaner product is compatible with gasoline of all types, safe for catalyst converters, oxygen sensors and valves. It is recommended to apply the product every 3100 miles of run. DOSAGE 250 ml of cleaner for 40-60 L (10-15 gal) of fuel PACKAGE Bottle 250 ml XA 40013 Due to the specific detergent properties, AtomEx Multi Cleaner: Safely and quickly removes all types of deposits and contaminations Cleans injectors, inlet valves and combustion chamber to the level of technical purity Restores engine power and its characteristics to the initial ones; Reduces fuel combustion Removes moisture from the fuel system Decreases the level of toxic components in the exhaust gases Due to the revitalizant, AtomEx Multi Cleaner: Forms firm antiwear coating on the fuel equipment parts directly during the mechanism operation Restores pump* performance to the nominal level and improves fuel dispersion Protects injector needle from hanging-up during operation on low-quality fuel Increases performance reliability and extends service life of fuel system parts *with pendulum or gear rollers

XADO Highway Atomic Metal Conditioner is an engine treatment designed for use during every oil change. Highway rebuilds worn metal, reduces friction, and protects treated metal from future wear. Highway contains a much smaller amount of Revitalizant than our Maximum and Tuning products, and it is specially formulated for use during every oil change. Use Highway to rebuild worn metal, reduce friction between moving parts, lubricate metal, and protect an engine from future wear. Highway delivers 5.5% (RF5.5) of the active ingredient, Revitalizant, necessary for a complete revitalization cycle of a vehicle. It also contains a 2D lubricant and a Metal Conditioner. This three-stage process helps reduce friction, increase compression, enhance lubrication, and of course rebuild and protect worn metal. As such it is recommended for use after every oil change to revitalize and protect your engine from wear. Highway works in all gasoline-powered, diesel-powered, and natural-gas powered engines. No matter how well a car is maintained, high heat and friction cause a car’s engine to become worn, scratched, and misshapen over time. Adding XADO Highway Atomic Metal Conditioner to your engine oil rebuilds worn engine metal and coats the rebuild metal at the friction points with a self-regulating layer of ceramic-metal to prevent future wear. XADO’s innovative patented nano-technology is the result of 20 years of research and development. When added to an automobile’s engine oil, Revitalizant rebuilds engine metal at the atomic level, rebuilding worn engine metal, reversing wear, restoring engine geometry, and adding a self-regulating layer of ceramic-metal protection to prevent future wear. XADO Revitalizant does not cake, flake, or alter oil viscosity. This makes it safe to use in even the most sensitive vehicles. XADO’s Revitalizant technology has been independently tested and proven to work. Revitalizant is unlike any other engine treatment, because it actually works to rebuild metal, targeting the source of engine wear instead of merely masking the symptoms. Revitalizant is activated by high heat and friction, so it only repairs metal at high-friction points where metal wear occurs. Revitalizant leaves crank-cases and non-friction metal unaffected. XADO Highway Atomic Metal Conditioner contains 5.5% of the Active ingredient necessary to Revitalize an automobile engine, so it is safe to use every oil change. Application of Atomic Metal Conditioner HighWay with Revitalizant Make sure automobile engine is warmed up to normal operating temperature. Turn off vehicle. Shake bottle of Atomic Metal Conditioner HighWay for one minute and ensure bottle is at room temperature so that contents flow freely. Pour contents into engine oil reservoir. Start car and let engine idle for five minutes. Then drive as you normally would. *Granules with atomic Revitalizant completely dissolve in motor oil at normal operating temperature. Keep out of reach of children. Avoid contact with skin and eyes. If swallowed, seek medical attention immediately and show this container or label to medical personnel. Avoid release into the environment; refer to special instructions/ material safety data sheet. Material safety data sheet is available for professional user on request. Note Atomic Metal Conditioner HighWay with Revitalizant can be combined with all types of motor oils, from full synthetic to mineral oils XADO Highway Atomic Metal Conditioner with revitalizant is effective for gasoline, LPG and diesel engines of passenger cars and small trucks with oil system up to 10 L Recommended to use during each oil change For a complete revitalization cycle it is recommended to use XADO Maximum 1 Stage (RF 100) Technology and certificates 3C EFFECT 3G generation Compensates current wear-out of engine Increases engine compression Restores lost oil pressure Protects metal parts from overheating and overloading Improves lubricating properties of oil and tribological characteristics of engine units Reduces fuel consumption Increases power and acceleration capability Decreases noise and vibration level Can double or triple the life of engine Decreases toxic carbon monoxide and dioxide emissions

REVITALIZANT® EX120 for diesel engines. EX120 Revitalizant is designed to restore, repair and protect all diesel engines. including high-powered and turbocharged engines, against metallic wear and tear. The gel forms a new cermet coating on friction surfaces (the engine parts grow in volume, restore their original geometry). As a result a renovated unit exceeds the performance level of a new one and will last 2-4 times longer. General characteristics of the cermet layer: microhardness – 750 kg/mm2 high corrosion resistance roughness Ra up to 0,06 mkm Application: Processing of the engine with the oil system 3-10 liters. Step 1: Squeeze out the contents of one tube of EX120 Revitalizant into the oil filer of the engine warmed up to the running temperature. Start the engine and let it idle run for 5-10 minutes. Step 2: Repeat the Step 1 after 62-155 miles. Step 3: Repeat the Step 2 after 62-155 miles. The treatment is complete after ~1,000 miles Dosage: Oil system volume, L 3-10 11-20 21-30 Tubes, pcs 3 6 9 Treatment scheme 1+1+1 2+2+2 3+3+3 Tubes for new engines 2 4 6 Note! Do not change the oil until thetreatment has finished New engines with less than 20,000 km (12,500 miles) of run should be treated in one go Revitalization is considered to be completed after approx 1,000 miles The treatment can be applied when the engine is idling (4 hours idling is equivalent to 124 miles) Overhauled engines should be treated in 3 stages according to the normal procedure. New engines should be treated in one step – 2 tubes at one time The protective cermet coating forms on any working mechanism; if the mechanism (engine) is in a badly worn state, the worn parts should be replaced Capability: During the engine operation cylinder piston group in area of upper “blind” spot, the details of Variable Valve Event and Lift (VVEL), slider bearer of bent and countershaft. Revitalizant contains constructional material which takes up the wear of details. Due to revitalization on the surface of friction pair a new multifunction gradient covering is formed with the number of necessary character rating and strenuous conditions. The details of the engine increase in volume by returning everything that was worn in the process of exploitation. This is an effect of repairmen. Obtained cover has unique properties: more solid, corrosionproof, low gritness. After revitalization details of engine reliably will serve up to 2-4 times longer. This is an effect of protection from wearing-out. Due to revitalization of an engine significantly increases and aligns compression in cylinder, reduces fuel consumption, increases adhesion and coasting of car, restores of oil pumps, turbo sites, axles and linings, cylinder bearing surfaces, removes ovality. An engine will work quietly and without any vibration. Due to revitalization it can be kept in a perfect condition. Technology and certificates 2G generation Restores and protects friction parts of the cylinder-piston group, crank and gas distributing mechanisms against wear-out Significantly reduces fuel consumption (up to 30% at idle run) Increases oil pressure to the nominal Regains and increases compression in cylinders Increases engine power, improves acceleration capability Decreases noise and vibration level up to 10 times Increases service life of the units up to 2-3 times Protects an engine from negative consequences of “cold” start Improves engine operation after 31-62 mi Maintains engine operation during 186 mi in case of oil leakage